Anesthesia Associates

Digital Respirometers large LCD readout display eliminates the confusion of reading a mechanical respirometer dial. Flow sensing unit has only one moving part, and is detachable from the control unit for ease of sterilization and cleaning. Unit may be washed, gas sterilized or cold sterilized. Comes ready to use with included 9V battery and one (1) circuit adapter (22 mm FxF). * Range: 0-200 liters * Measurement Type: Air/Gas volume flow * Resolutions: 0.02 liter * Flow Rate: 5 LPM minimum/150 LPM maximum * Accuracy: ±2% at calibration point * Resistance to flow: 2 cm of water at 100 LPM * Inlet and Outlet sizes: 22 mm Male

These Endotracheal Tube Connectors are made of chrome plated brass making them durable and rugged. The reusable ETT connector curved back to within 60 or 90-degrees of itself and feature 15mm Male by nipple sizes 4 to 6mm I.D. The 'mm” size designation in ETT adaptors indicate the inside diameter of the product to match the ID of the ETT. Fit into the ETT will be tight on most tubes, depending on stiffness (a warmed ET Tube end can help with insertion). Features: * Made of Chromed Brass * Machine End Connection: 15mm Male * Patient End Connection 4 to 6mm ID Nipple * Available in 60 and 90-degree curves * Reusable * Knurled Flange for Grip * Durable and Rugged * Latex-free

Analog Wright Respirometers feature a push button style ON/OFF and RESET control. The units are designed with case seals and material selections to withstand ETO sterilization only. The respirometers have 22mm Male Inlet and Outlets. * Range: 0-100 liters * Material: Chromed Brass * Analog Dial (separate large and small dials) * Inlet and Outlet sizes: 22 mm Male

CPAP mask elbow has fresh gas feed tube within 9/16” of the mask fitting, allowing kinetic energy of incoming gases to decrease dead space. Key Benefits: * Pop-Off Valve * Non-Conductive * Anodized Aluminum Connections: * Machine end: 15 mm Male * Patient end: nominal 22 mm Male and 15 mm Female

Lightweight anodized aluminum bagtail bleed valve designed for replacement with Dupaco 32025.

CPAP Mask Elbows with feed tube at top, spring-loaded pop-off adjustable valve, and 1/4in connection for pressure manometer. Kinetic energy of the incoming gases decreases dead space in the elbow because fresh gas tube is within 9/16in of the mask filling. Features: * Machine end: 15mm Male * Patient end: nominal 22mm Male and 15mm Female * Pop-off valve * Chrome plated brass * Latex-free

Suction stylette is made of soft malleable copper.

Mounted on rear of controller, connects to sensing unit. Replacement plug for Digital Respirometer (07-00-295). Features: * Reusable * Latex-free * For use with Digital Respirometer (Item # 07-00-295)

Replacement control unit designed for electronic digital respirometer. Features: * Range: 0-200 liters * Measurement Type: Air/Gas volume flow * Resolutions: 0.02 liter * Flow Rate: 5 LPM minimum/150 LPM maximum * Accuracy: ±2% at calibration point * Resistance to flow: 2 cm of water at 100 LPM * Inlet and Outlet sizes: 22 mm Male

Replacement flow sensing unit, for digital respirometer. Flow sensing unit only with adapter fitting. For use with Digital Respirometer (07-00-295). Features: * Reusable * Latex-free * 22mm Male Inlet and Outlet * Flow Range: 5-150LPM * Accuracy: +/-2% at calibration point * Rugged and Sterilizable

Manometer features include: * 2.5 inch diameter chrome plated case * 1/4in NPT Male Bottom connection * Front zero correcting screw

Head harnesses large holes permit ventilation but will not slip over small heads. Pressure is equally distributed over a large area.

Rugged and reusable manual jet ventilator system is designed for rigid-wall bronchoscopy, laryngeal micro-surgery, and emergency use.Manual jet ventilator consists of: * high pressure inlet tubing with 02 DISS fitting * flow control valve * thumb control valve * back-pressure gauge * 2 foot clear plastic outlet tubing with Luer Lock fitting for attachment of adapters and tubes * Hoses and inlet fitting are customizable to user needs

#00-199 Manometer with P-159 "Tee" (1/4in tube) and #00-273 APL valve adjustable from 0-55 cm H20 at 9 LPM. Includes resettable pointer to capture maximum pressure or vacuum reading.

Magill forceps are made of highly-polished stainless steel. Closed tip (closes completely) and open eye design easily positions ETT's during blind nasal intubation.

Gardent tooth protectors are designed to protect teeth from impact and prying forces during intubation. They are molded in the USA using soft Santoprene TPE. Features: * Use during intubation * Adult patients * Disposable * Latex Free * MR Safe

Respirometer Guard is designed to reduce physical damage due to dropping and abuse. Made out of attractive and durable - latex free Neoprene - that can be reliably sterilized. Shipped as a kit with two (2) case closure O-Rings, and is easily installed.

Extended length retractile cable designed for use with electronic digital respirometer.

Abelson Jaw Spreader is intended for spreading the jaws in trismus associated with convulsive seizures or other Locked Jaw conditions.

Reusable connector tube designed of flexible EPDM synthetic rubber (black) and 15mm Male x 15mm Female with Delrin ends.

Williams Airway Intubator is indicated for use as: * Oropharyngeal airway * Means of intubating the trachea * Guide for fiber optic laryngoscope placement

Flexible Teflon Connector (transparent/white) designed with 15 mm Male by 15 mm Female ends. Ends are firmly threaded into the convolutions of the tubing making it easy to assemble connections of different lengths. Connector is inert, long-lasting, lightweight, flexible, translucent, and heat sterilizable.

Reusable, fluted, breathing bag. Made from conductive black neoprene.

Flexible, semi-transparent, 9/16in smooth I.D. spiral reinforced tubing. Ends are: rigid 15mm Male by Silicone 15mm Female. Autoclavable. Lightweight, Cream Colored Polyester (Latex Free), 12in overall length